Datalogic QLM700 Manuale delle Istruzioni Pagina 60
- Pagina / 160
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
MATRIX 300™ REFERENCE MANUAL
48
4
4 CBX ELECTRICAL CONNECTIONS
All Matrix 300™ models can be connected to a CBX connection box through one of the
available CAB-DSxx-S accessory cables. These accessory cables terminate in an M12 17-
pin connector on the Matrix 300™ side and in a 25-pin male D-sub connector on the CBX
side.
We recommend making system connections through one of the CBX connection boxes since
they offer the advantages of easy connection, easy device replacement, opto-isolated
outputs (Outputs 1 and 2), and filtered reference signals.
NOTE: If you require direct wiring to the reader the connections are the
same as shown in this chapter with the exception of the digital Outputs. Direct
wiring details are indicated in Appendix A
The table below gives the pinout of the CBX100/500 terminal block connectors. Use this
pinout when the Matrix 300™ reader is connected by means of the CBX100/500:
CBX100/500 Terminal Block Connectors
Input Power
Vdc
Power Supply Input Voltage +
GND
Power Supply Input Voltage -
Earth
Protection Earth Ground
Inputs
+V
Power Source – External Trigger
I1A
External Trigger A (polarity insensitive)
I1B
External Trigger B (polarity insensitive)
-V
Power Reference – External Trigger
+V
Power Source – Inputs
I2A
Input 2 A (polarity insensitive)
I2B
Input 2 B (polarity insensitive)
-V
Power Reference – Inputs
Outputs
+V
Power Source - Outputs
-V
Power Reference - Outputs
O1+
Output 1 + opto-isolated and polarity sensitive
O1-
Output 1 - opto-isolated and polarity sensitive
O2+
Output 2 + opto-isolated and polarity sensitive
O2-
Output 2 - opto-isolated and polarity sensitive
03A
Output 3 non opto-isolated (only available on CBX500)
Auxiliary Interface
TX
Auxiliary Interface TX
RX
Auxiliary Interface RX
SGND
Auxiliary Interface Reference
ID-NET™
REF
Network Reference
ID+
ID-NET™ network +
ID-
ID-NET™ network -
Shield
Network Cable Shield
Main Interface
RS232
RS485/422 Full-Duplex
TX
TX+
RX
*RX+
RTS
TX-
CTS
*RX-
SGND
SGND
* Do not leave floating, see par. 4.2.2 for connection details.
- REFERENCE MANUAL 1
- CONTENTS 3
- REFERENCES 6
- COMPLIANCE 7
- LASER SAFETY 8
- LED SAFETY 8
- HANDLING 9
- GENERAL VIEW 11
- Matrix 300™ 12
- 1 RAPID CONFIGURATION 13
- RAPID CONFIGURATION 17
- STEP 7 – TEST MODE 30
- Host Mode Programming 31
- Alternative Layouts 31
- 2 INTRODUCTION 32
- INTRODUCTION 33
- Figure 13 - Indicators 35
- 2.3 ID-NET™ 36
- VISISET™ 41
- Restore 42
- Replacement 43
- 2.5.1 X-PRESS™ Functions 46
- Test Mode (Function 1) 47
- Aim/Autofocus (Function 2) 47
- Setup (Function 3) 47
- Learn (Function 4) 48
- 2.5.2 Diagnostic Indication 48
- 2.6 MODEL DESCRIPTION 48
- 2.6.1 Lighting System Notes 49
- 2.7 ACCESSORIES 49
- 2.8 APPLICATION EXAMPLES 50
- 2.8.1 Document Handling 50
- 2.8.3 Direct Part Marking 51
- 3 INSTALLATION 53
- 3.2 MECHANICAL DIMENSIONS 54
- INSTALLATION 55
- No Pitch, Tilt or Skew 58
- 4.1 POWER SUPPLY 61
- 4.1.1 Standard Models 61
- 4.2 MAIN SERIAL INTERFACE 63
- 4.2.1 RS232 Interface 64
- CBX ELECTRICAL CONNECTIONS 65
- 4.3 ID-NET™ INTERFACE 66
- 4.3.1 ID-NET™ Cables 66
- 4.3.2 ID-NET™ Response Time 67
- 4.5 INPUTS 72
- NPN Photocell 73
- PNP Photocell 73
- PH-1 Photocell (PNP) 73
- 4.6 OUTPUTS 76
- 5 TYPICAL LAYOUTS 80
- BA600 ID-NET™ Out 84
- BA400 Ext. Power 84
- BA500 Trigger 84
- BA300 Service 84
- Fieldbus Interface 85
- 5.4 PASS-THROUGH 89
- 5.5 ETHERNET CONNECTION 90
- TYPICAL LAYOUTS 91
- Ethernet Interface 91
- 6 READING FEATURES 92
- 6.2 READING DIAGRAMS 95
- 6.3.1 1D (Linear) Codes 96
- 6.4.1 1D (Linear) Codes 105
- READING FEATURES 113
- Line Speed 114
- 7 SOFTWARE CONFIGURATION 115
- 7.3 STARTUP 116
- 7.3.1 VisiSet™ Options 117
- MATRIX 300™ REFERENCE MANUAL 118
- SOFTWARE CONFIGURATION 119
- 7.5 CONFIGURATION 120
- 7.5.3 Calibration 127
- Same Phase) 131
- 7.7 STATISTICS 141
- 8 MAINTENANCE 142
- 9 TROUBLESHOOTING 143
- 10 TECHNICAL FEATURES 146
- TECHNICAL FEATURES 147
- A ALTERNATIVE CONNECTIONS 148
- ON-BOARD ETHERNET CONNECTOR 149
- ID-NET™ NETWORK TERMINATION 151
- OUTPUTS 152
- USER INTERFACE 153
- USER INTERFACE - SERIAL HOST 154
- GLOSSARY 155
- DECLARATION OF CONFORMITY 159
Prodotti e manuali riguardandi Gateway/Controller Datalogic QLM700
(34 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale